Sometines the gear is broke clean off, and sometimes it's just stripped off the plastic pegs that hold it on. they optics are a very common failure but another common problem when the complaint is no ice production is the water line supplying the ice maker is frozen. Close the emitter flapper and the light should stay on. (Make sure there is nothing to block the path) If this checks ok, than your problem is likely to lie within The red light your seeing is to your emitter receiver board for your ice maker. this content
The content on this web site is for informational purposes only and is not intended to replace an on-site diagnosis from a qualified appliance service technician. Close the freezer door. She has several years of experience in the home-improvement industry, focusing on gardening, and a background in group exercise instruction. When I look at the optics beam hole on the left side I do not see any flashing lights, does that mean the control boards are bad or is it the
Tente novamente mais tarde. do not block light single. I will be here. No problem. Ask Your Own Appliance Question Customer: replied5 years ago.
Thanks for any responses Reply Ryan Posted on May 13, 2015 Yes, it sounds like the optic boards are bad based on what you have described. replied5 years ago. Make sure you're not blocking any of those - that tells the ice maker to shut off. Kenmore Ice Maker Red Light Blinking Twice The information Barbara provided you is good.
I will get the instructions together for that in just a minute. Kenmore Refrigerator Ice Maker Not Making Ice Reply Ryan Posted on September 17, 2015 Refrigerators take a while to cool down and start making ice. You may have to register before you can post: click the register link above to proceed. Under that you will see 3 phillps screws.
Repeat Step 3 to reset the ice maker. this If so, defrost it with a hair dryer and stick something up in there to see if you got all the ice out. Kitchenaid Superba Ice Maker Not Working What's New? Kitchenaid Refrigerator Not Making Ice Red Light Blinking Save the screws.
I've defrosted everything. news Reply Ryan Posted on June 14, 2015 The ice maker has to be cold enough to start making ice. Leave the door closed for at least 10 seconds. out of box M Get Weekly DIY Guides & Inspiration Life Made Easier. Whirlpool Ice Maker Red Light Flashing
Fechar Saiba mais View this message in English Você está visualizando o YouTube em Português (Brasil). É possível alterar essa preferência abaixo. French Door ... I would use a better inline filter on my water line if I were concerned. http://pixelzs.com/ice-maker/kitchenaid-ice-maker-not-working-red-light-blinking.html I am planning a buildout on my garden level that will include a snack bar which will have a ref.
I unplugged the refridgerator for about a minute and plugged it back in. 30 minutes later-ICE! Kenmore Ice Maker Led Blinking Codes Take those out and pull the brown/tan module off. This part has been discontinued by the manufacture, so you will either need to look for a used one or a company that can rebuild your existing control board.
ft. If the light continues to flash, replace the ice maker control and the emitter switch. I unplugged the jumper and the LED shut off. Kenmore Bottom Freezer Ice Maker Not Working It's blinking twice, and then pauses.
Thank you for choosing Manage My Life. Place icemaker back in freezer and close the freezer door. I also saw this page - http://laminateflooring.oncloud8.com/archive.php/o_t__t_7081__icemaker-problem.htmlbut no luck on the meaning of the red light. check my blog The part number is W10190935.http://midwayparts.net/midwayparts/zen-cart-v1.3.8a-full-fileset-12112007/index.php?main_page=product_info&cPath=3&products_id=49To replace the module remove the white end cap pictured below.
I ordered a new set of controller boards for the level controller and the system began working a day before the boards arrived. I just went to check it, and it's now not blinking (Murphy's Law!). New Topic Reply Printer Friendly KitchenAid icemaker not working; blinking red LED Rating: Rate This Topic Excellent Good Fair Poor Horrible AuthorPost Posted: Tue Apr 26th, 2005 03:12 am PM Josh Reply With Quote December 17th, 2009,02:29 AM #8 Jake View Profile View Forum Posts Visit Homepage Appliance Tech - Admin Join Date Aug 2004 Location McMullen Valley, Arizona Posts 80,043
ft. 33" Top-Freezer ... When I do that, the control beam comes on red for about 10 seconds and then goes off, completely, regardless of the light control flapper position.