Fix Iphone 3g Not Working After Replacing Screen (Solved)

Home > Iphone 3g > Iphone 3g Not Working After Replacing Screen

Iphone 3g Not Working After Replacing Screen

If there's nothing wrong with the connection then it usually works without the foam piece, but the piece will sometimes give it that extra pressure when closed to help. TechRax 30,330,785 views 4:36 Blank screen in iPhone 3GS - Duration: 5:49. iPhone OS 2.x and earlier: Press and hold the Home button until the application quits. Or I need some other tstuff like Glue and so on? have a peek here

The other trick is to get the suction cup as close as possible to the button to increase the leverage. Thanks! Between these two parts, with a proper lighting, it is easier to see where to insert the connector. MostAmazingTop10 959,680 views 6:33 14 Things You Didn't know You Could do With an iPhone! - Duration: 6:45. https://www.ifixit.com/Answers/View/79028/Phone+not+working+after+replacing+LCD+screen

Yet my iphone screen is shattered all through out and the cup who stay due to air coming through the glass. Cancel wefixIT Rep: 1 1 1 Posted: 01/25/2013 Options Permalink History OK! The phone LCD is completely dead.

So I had to figure out how the 3 ribbons worked. If there are blue traces of Loctite, you may need to use the tip of a soldering iron to briefly heat the screw so that you can remove it. PileOfMush - 08/26/2009 Reply Failed :( I didn't found the way to lift and broke in 2 the connector for #3. There is a white line with an arrow.

For my next attempt, I stuck the screwdriver under the side of the tab and gently lifted. You had any luck yet? Yes No Voted Undo Score 0 Cancel Add a comment 0/1024 Cancel Post comment Are you sure you want to delete this zzzzzz? Voila.

Leon Stacey 10,889 views 5:49 iPhone Screen Is Frozen: How to Fix : Tech Yeah! - Duration: 1:36. You can not post a blank message. any advice. cables weren't seated correctly for me and i experienced the same issue.

Jan 11, 2010 7:25 PM Helpful (0) Reply options Link to this post by modular747, modular747 Jan 12, 2010 3:57 AM in response to Brian965 Level 6 (19,343 points) iPad Jan read this article jasleen281 53,080 views 4:30 How To Replace Iphone Digitizer (Glass) 3g 3gs - Duration: 20:28. 00mattyvhowto00 84,505 views 20:28 How to fix the IPhone 3G frozen screen - Duration: 1:11. Cancel Willy Rep: 1 Posted: 06/29/2012 Options Permalink History Thanks a lot ;-) I installed a program and it got frozen, reactivation with power home, but stays on the startup logo. After reassembly this resulted in a black screen.

but i have done something extra wrong with a part that is not labeled and it is a part that i cannot see in these videos that is never addressed. navigate here perhaps your screen sits a bit akimbo because you still have some goo in those rails? Also a question for everyone... other than that make sure you have the right part and try hard reset after you've reconnected.

Finally I went to troubleshoot the display at Apple (http://support.apple.com/kb/HT1737) where I reset it and then reset all settings. i instaled it and pluged it to recharge abouth 1 hour and it dont whant to start. My 16GB 3G has a cable glued to the bottom left side of the LCD. Check This Out Ryan Hollis - 06/15/2010 Quote from jdangler: I forgot to put the tape back on.

br1ansk - 01/02/2015 Reply Add a comment Add Comment 1024 Almost done! Was this answer helpful? Good call you guys - cheers! 07/21/2011 by brendan +1 for Steve!

deanmcrobie - 10/08/2009 Reply so the kit I got sent me all the tools I need including the glass panel but step 12 said to separate the lcd from the glass

Yes No Voted Undo Score 1 Cancel Add a comment 0/1024 Cancel Post comment Are you sure you want to delete this zzzzzz? Thank you so much!! 10/08/2011 by nic I had this to also my battery acted like it was dead so I tore down the phone and took a small paint brush This will keep glass shards contained and provide structural integrity when prying and lifting the display. mauritscassee - 06/28/2009 Reply Quote from mauritscassee: Press the metal spudger between the chrome bezel and the screen, than use the suction cup.

i had to spend quite a bit of time (30 minutes) on the hair dryer/heat up step to gently heat then gently loosen the adhesive holding the front glass to the Cancel edcimo Rep: 25 1 Posted: 10/29/2011 Options Permalink History Once the screen would light up faintly but stay black, we called the iphone and when it lit up faintly again, It's easier and safer to grip the suction cup's base instead of the metal handle. this contact form after successfully removing the glass (and shards of glass from my broken screen) i also had some clean up to do to remove the excess glue and adhesive from both the

Very nice sunday indeed... all sound brilliant, but it has got a bright, white screen. I replaced he digitizer and my LCD seemed to stop working after I replaced the cracked screen. Repair of this device is similar to the 3G, and requires simple screwdrivers and prying tools.

We simply snapped the connector back on, and VOILA, GPS works again. About a year ago I had washed an iPhone 3G in the washing machine...after I got a new one, I took the old one apart just to see what it was Show more Language: English Content location: United States Restricted Mode: Off History Help Loading... I turned on my iPhone by accident during repair.

tware - 09/24/2009 Reply I successfully completed the project, but have one issue. Then I tried to wiggle ribbon three in to the white connector - - then I realized it goes UNDER the white connector. Mine got wet and I dried it for days in a bag of rice. Cancel Ryan Rep: 1 Posted: 07/04/2013 Options Permalink History I have the same problem...