How To Repair Iphone 3gs Side Buttons Not Working (Solved)

Home > Iphone 3gs > Iphone 3gs Side Buttons Not Working

Iphone 3gs Side Buttons Not Working

Excellent directions! The plastic seemed very brittle; the phone is 4 years old. The battery is attached with an adhesive strip around the perimeter of the battery. Feb 3, 2012 3:03 AM Helpful (0) Reply options Link to this post by tedmoseby123, tedmoseby123 Jun 2, 2012 8:31 AM in response to evansonoda Level 1 (0 points) Jun 2, have a peek here

Thank you! I hope this is helpful. Techscinium 348,580 views 3:15 iPhone 6 Clone Unboxing! - Duration: 8:32. I must have one of the unique (Chinese) versions and while trying to lift up, I should have been sliding back.

Press down on the tool until the SIM card tray pops out. satsho - 03/16/2012 I agree with the others that cable 6 and 7 are very fragile and can be difficult to reattach. good luck!tedmoseby123 Jun 2, 2012 8:31 AM Helpful (1) Reply options Link to this post by bettylynn, bettylynn Jul 4, 2012 2:31 PM in response to tedmoseby123 Level 1 (0 points)

I'm currently waiting for mine... :) Turbo Fredriksson - 04/03/2010 Reply [quote|I'm currently waiting for mine... :)[/quote] And my younger brother managed to replace it with only a couple of minutes I have the same Problem: Pressing PowerButton, Display turns on, Apple Logo ... Brian - 01/23/2012 Reply When reassembling I found the screwhole for the longer screw (on the right) was full of glue. Autoplay When autoplay is enabled, a suggested video will automatically play next.

Hmmm. How do I remove the metal housing? Enable Assistive Touch to Gain Software Power Buttons Before going any further, you'll want to enable Assistive Touch to gain access to the onscreen hardware buttons. chuvux - 04/20/2012 Reply There were many places where I wished there were clearer instructions on putting it back together; this was a big one.

Use a spudger to flip up the white plastic tab holding the ribbon cable "3" in place. if I can't fix it, I'll have to get a new phone since I can't see myself hearing only via Bluetooth or speakerphone. I have set of new screws here an I need to sort them - I can't find any specifications on the two screws mentioned here. And if anyone knows where to buy a replacement flip tab, that'd be cool too :) cliffcurtis - 08/06/2009 Reply I should also note that I used a little flat head

ratioswitch - 01/26/2010 Reply Installed and the phone is working... Find other models on our main iPhone repair page. The switch that you stuck to the bracket by removing the tape backing must also be in the muted position (pushed down toward the back of the case). When you reverse the steps to reassemble the phone - make sure to get all 6 (or 7 for the 3GS) cables plugged back in.

Anyone know what i should do to fix this? navigate here taneliteittinen - 12/19/2011 Reply What if I have one of those thin film screen protectors applied, would the suction cup peel it right off instead of lifting the screen up? Yes No Voted Undo Score 0 Cancel Add a comment 0/1024 Cancel Post comment Are you sure you want to delete this zzzzzz? It will not recover from this cycle until I plug it in to the computer.

Just need to go out and buy some 'electrical cleaning solvent' or whatever it can be named :) Was this answer helpful? Quote from Vishal Vaidya: Is there a way of replacing the connector? My seems to keep dropping out and the ear speaker is not working. Check This Out Tom Brandolini - 08/03/2014 Add a comment Add Comment 1024 Step 12 Edit Remove the following 8 screws: Five 2.3 mm Phillips #00 screws with partial threads securing the logic board

I'd be in your debt if you could help -and I'm sure there are others here too who'd appreciate it! Add a comment Add a comment Add Comment 1024 Step 24 Edit Remove the two Phillips #00 screws securing the vibrator to the rear panel. mattfife - 04/15/2011 Reply I found removal of the batt was easier to accomplish by prying slightly and slowly around, starting from the edge opposite the Volume control.

If it's not centered and you apply pressure you will very likely destroy both halves of the connector.

By the way, my mute button is a little short (non Apple genuine part ??) and do not exit correctly through the hole of the back of my 3GS: it is So Here's what I did with success: I lightly moistened a cotton ball with regular rubbing alcohol and then gently passed it over the on/off button (upper right top) several times Thanks. I took my switch apart and will try to clean it (mine was dropped in water by previous owner).

Turbo Fredriksson - 04/03/2010 Reply Quote from Turbo Fredriksson: Aparently #3 is 'Earpiece & Proximity Sensor'. Two 2.3 mm Phillips #00 screws with full threads securing the logic board and camera. iResQ Coupon Info! this contact form Installation should push the jack down then slide into place.

No phone shops seem to be able to change it for me. thanks !!! Jon Evans - 11/20/2009 Reply When the instructions say "Rotate the display assembly up until it is at an angle of approximately 45 degrees." they really mean "TILT THE HOME BUTTON and you'll have to pull all the screws back out and figure out what you did wrong (and why you had a naggling suspicion the logic board wasn't placed quite right).

Yes No Voted Undo Score 8 Cancel Comments: The squeezing trick worked for mine- thanks Mark!!! 11/09/2013 by Dave Wow, had some problem and this worked for me! But if you guys found another solution let me know! Allow it to guide your logic board into the proper place. I mistakenly tried to pry up the wrong piece, but fortunately didn't do too much damage before I realized this.

I now have a dead spot on the screen. Problem solved by inserting the screw driver in the s-cup, which gave just the right leverage to control pulling loose the display assembly. What is this system like, and is it worth trying to fix it myself? June 28 by mipz28 Show 1 more comment Add a comment 0/1024 Cancel Post comment Are you sure you want to delete this zzzzzz?

Naim Limani 17,036 views 1:37 iPhone 5 Power & Volume Button Repair - Duration: 7:35. I finally had to give up. Category Science & Technology License Standard YouTube License Show more Show less Loading...