How To Fix Iphone 3gs Vibrate Button Not Working (Solved)

Home > Iphone 3gs > Iphone 3gs Vibrate Button Not Working

Iphone 3gs Vibrate Button Not Working

Quick view Add to Wishlist Add to Compare iPhone 3G Glass Repair $49.99 Sale! I was very lucky. TechRax 30,330,785 views 4:36 iPhone 3G S vibration switch issue - pre Apple visit video. - Duration: 1:58. Here you will see a button with a bell(on the extreme left). have a peek here

Add a comment Add a comment Add Comment 1024 Step 22 Edit Carefully lift the headphone jack assembly out of the iPhone. Add to Compare Add to my wishlist More info Reviews Description: If your vibrate switch is stuck or not functioning, choose this iPhone 3G repair and iPhone 3Gs repair. Dennis Smith denniskristen - 05/15/2013 Reply I strongly recommend that you review Step 7 of the 3GS 'Display,' 'Front Panel' or 'Front Panel Assembly' guide. Take note of its position and orientation for later reinstallation. https://discussions.apple.com/thread/2590157?tstart=0

Quote from John: I've done all the steps and phone switches on and works just fine with the one exception that I do have a signal! paolo - 06/22/2010 Reply while re assembling i couldnt for the life of me figure out where the metal plate thing off the camera went until i saw the gap for There is a small plastic spacer adhered to the inside of button which may come off with cleaning. I must have one of the unique (Chinese) versions and while trying to lift up, I should have been sliding back.

But if you had to ask if it can be replaced, you don't have knowledge to do it yourself! Considered it the hardest part of the tutorial. The end result of any such mishap is commonly either a broken screen, broken mute button or malfunctioning volume buttons and headphone jack and in worst of the cases, all at Cor Berkelaar - 03/27/2010 Reply Quote from Cor Berkelaar: How on earth do I get the black ribbon cable back into its connector???

Hey, I have a great little screwdriver. How can I tell whether it is fully inserted? I would rate the repairability of this phone lower than it is because of the 50-50 chance of flattening these connectors. https://www.ifixit.com/Guide/iPhone+3G+Mute+Button+Replacement/581 Flat renting in Berlin for medium-term period My boss asks me to stop writing small functions and do everything in the same loop Coworker throwing cigarettes out of a car, I

I heard a snap when mine went into place. Fine point tweezers would help here, to take it out and to put back in place during re-assembly. what to do now ??? also in the "settings" you can set it there as well.

When replacing the logic board after installing battery, connect the camera to the logic board before inserting it into the case.

When you assemble it, you would apply pressure to the ribbon to insert it back into the ribbon "socket." Some iPhones may have the connector colors reversed (black plastic tab, white Since my mission was not to mess with or replace the battery anyways I just left it alone. My phone was replaced on warranty in February so this must be the case in some newer 3G's.

Method 2: Cydia Tweaks (Applies To Jailbroken Phones) If you have a jailbroken phone, you can visit Cydia and download any of the available tweaks that will help you switch between navigate here Great! John Zemko - 07/29/2010 Reply As mentioned, some 3g phones there is a small metal clip holding down the camera (held in place by the screw there). I had one scary moment where my screen would not turn on but a Hard Reset on the phone fixed it.

rclyons - 06/22/2013 Reply Add a comment Add Comment 1024 Step 15 Edit Slide the logic board towards the dock connector and out of the iPhone. Then realized the next day I also had missed connector 6 (wifi). Good directions. Check This Out HaJo Schatz - 11/10/2012 Reply My American 3GS white connector did not flip open.

So using a sharp cutter, I cut a bit hole. The pressure wasn't too strong, but it doesn't just slide right in. perfect Instructions.

Was this answer helpful?

Currently my iPhone has become an iPod! Volume and mute control again! Prying the battery up from its adhesive was the hardest part of this repair, and yes, I did break the spudger thingy. Sign in Share More Report Need to report the video?

You can tell where this piece is supposed to go because you will see a small edge, (on the inside of the exterior part of the switch) and a thin grey Luckily, you can remove just the camera enclosure from the 3GS and transplant it to the 3G. Marc Tobe - 10/04/2011 You might also want to have a little tweezer which comes in very handy when reassembling the phone Mathias - 04/21/2012 Reply Do seriously consider ESD when this contact form Total products (tax excl.): Total shipping(tax excl.) Free shipping!

The ribbon cable is easily damaged - be very gentle. What should I do? jargogle - 09/15/2011 Reply Agree with this comment. Allow it to guide your logic board into the proper place.

would that be the reason that the iPhone would not start even though the ribbon is in the connector and fastened secured with the white plastic tab is down. Without this "comfortable" fit, you won't be able to get the SIM in.