(Solved) Iphone 4 Internal Ear Speaker Not Working Tutorial

Home > Not Working > Iphone 4 Internal Ear Speaker Not Working

Iphone 4 Internal Ear Speaker Not Working

Contents

It is a circular nut that helps the WiFi antenna get a good connection to the logic board. Judy - 04/30/2014 Reply Does any one know where to source a replacement for the little round "nut" trapped between shield and nut. Looking forward to replacing the battery in my other phone that has the pentalobe screws. Elige tu idioma. Source

If one part is resistant move your pry tool a little further down and gently start prying it up in different places taking care not to come too close to the Yes No Voted Undo Score 1 Cancel Comments: Well, it was not the earpiece. It must be reinserted prior to installing the shield, with the thick part up and the spring in contact with the gold pad to the right of the screw hole in Iniciar sesión Compartir Más Denunciar ¿Quieres informar del vídeo? visit

Iphone 4 Ear Speaker Not Working

Damaged antenna? gregjames - 07/06/2012 Reply This was absolutely the hardest part - had to do it over many times. dfrisch86 - 01/22/2014 Reply Installed new battery without a problem.

I left it out, and my touchscreen had all sorts of problem. I had no wifi at all until this was present. iPhoneRepairMia 130.391 visualizaciones 8:11 7 vídeos Reproducir todo Thay Loa Trong ip 4sTeo Nguyen Van iPhone 4, Como reparar el problema del Audio Decoder IC Chip - Duración: 18:22. Iphone Ear Speaker Very Quiet When replacing my home button, I noticed this rubber piece fall out of the phone, and couldn't figure out where it went.

share Share on Twitter Share on Facebook Email Link Like + Quote Reply Zzsr81, Jan 13, 2012 Zzsr81 macrumors newbie Joined: Jan 13, 2012 #12 I'm having the exact same problem- Iphone 6 Ear Speaker Not Working share Share on Twitter Share on Facebook Email Link Like + Quote Reply Stuos, Jun 13, 2012 Stuos macrumors newbie Joined: Jun 13, 2012 #14 iphone 4 earpiece not working Just Battery was glued firmly in, so I loosened it from the outside instead of using the plastic pull-tab. romaine - 05/15/2011 Reply If you are replacing any of the cables that connect here, be sure to save the foam from the top of the connector to put on your

It seems it should be captive soldered to the MB, but it comes lose... Iphone 4 Ear Speaker Not Working Solution The reason why I say don't use an implement to try lift the battery is because far too many times I've seen punctured & bent batteries come in to this workshop If not torqued down, the shield will be above the plane of the frame and the back will not slide into place in step 2. Is there any water damage done to the phone?

Iphone 6 Ear Speaker Not Working

Aug 7, 2012 6:31 PM Helpful (0) Reply options Link to this post by Karen_Schwalbe, Karen_Schwalbe Aug 11, 2012 9:41 AM in response to Akssak Level 1 (0 points) Aug 11, How did you get it to not kink while placing the batter back into the phone? Iphone 4 Ear Speaker Not Working share Share on Twitter Share on Facebook Email Link Like + Quote Reply ECUpirate44, Dec 9, 2011 ECUpirate44 thread starter macrumors 603 Joined: Mar 22, 2010 Location: NC #6 It fixed Iphone 5 Earpiece Not Working One kink in this could sever the battery leads.

dreyna - 08/12/2011 Reply Great point! this contact form Please help! Cancel Rahul Rep: 13 1 Posted: 12/21/2014 Options Permalink History Koo.. nickbits - 06/01/2012 Reply Take care to put the small ruber piece into place to protect the ribon cable for the lcd dyplay Hanspeter - 10/04/2012 Reply The smallest screw below Iphone Earpiece Not Working But Speaker Does

If those are not bent up enough (laying flat) you won't have contact with the logic board... Seems to be working fine now.... carefull with the ribbon on the edge of the board... http://pixelzs.com/not-working/iphone-internal-speaker-not-working-after-screen-replacement.html Gently lift the shield out of the iPhone and set it aside.Take your spudger tool and gently pry up the dock connector cable and peel it back as shown below.

Añadir a ¿Quieres volver a verlo más tarde? Iphone 6s Earpiece Not Working the adhesive on the battery tends to be under the edge of the battery nearest the center of the phone. Want to know how to perform another type of iPhone repair or modification?

Jul 31, 2012 9:42 AM Helpful (0) Reply options Link to this post by ZOZ2112, ZOZ2112 Jul 31, 2012 7:06 PM in response to im2hot4ya Level 1 (0 points) Jul 31,

Additional resources: How to replace the battery in an iPhone 4S How to replace the rear-facing camera in an iPhone 4S Even more DIY guides and repair walkthroughs Like us! Stefan - 12/16/2012 Reply Add a comment Add Comment 1024 Step 10 Edit Carefully peel the dock ribbon cable off the logic board and the lower speaker enclosure. Glad I got the 54 Bit kit! Iphone Ear Speaker Not Working Water Just when I hold it up to my ear normally, there is no sound.

It must be a loose connection of the earpiece to the circuit board (I must admit the phone has had some nasty falls though). thanks.. Try Reset All Settings, Home Screen -> Settings -> General -> Reset -> Reset All Settings. http://pixelzs.com/not-working/iphone-3gs-internal-speaker-not-working-after-screen-replacement.html Joshua - 06/01/2013 When reassembling, ensure the ribbon cables for the connector are between the silver metal and the circuit board.

Hopefully no harm done. johnpetraborg - 02/10/2011 Reply It seems that you misunderstood the notes throughout the guide. Do not stick anything in the jack. I'd add a distinct warnig here to use the right (short) one.

Scott - 03/02/2012 Reply Ear piece metal connectors: You can see them on step 22. I thought "no way this is going to work", but it did!!! Jimmy - 12/26/2011 When re-assembling, start off with replacing the 4.8 mm Philips screw first, then the 2.3 mm. Remove the earpiece speaker. 3 comments Tip: The earpiece speaker consists of two small contacts (that is place against the MB) that can only be bent.

I found out that I had broken the tiny jumper on the main board when I pried off the headphone plug. Thank you so much for this trick to fix. Remember which screw came from where as they are different sizes. I have this bad feeling that is may be broken inside.

What have I not done coreectly - or at least what can I check to determine the problem? splaye - 06/23/2014 Add a comment Add Comment 1024 Step 4 Battery Edit Remove the single 2.5 mm Phillips screw securing the battery connector to the logic board. Was going to sell on ebay but now I can not.