Yes No Voted Undo Score 0 Cancel Add a comment 0/1024 Cancel Post comment Are you sure you want to delete this zzzzzz? The oils on your fingers have the potential to cause wireless interference issues. 3 comments Be careful to make sure you don't pinch the clear plastic tab under the mobo when No posts that aren’t directly related to Apple or the Apple eco-system. Add to Want to watch this again later? http://pixelzs.com/power-button/iphone-4s-power-button-not-working.html
Before reassembly, be sure to clean all metal-to-metal contact points on the dock connector cable cover with a de-greaser such as windex. In May, a nearly identical case was filed against Apple, in which the plaintiff argues that the flex cable mechanism attached to the power button, which we've found is the cause I clicked the clip into the socket first and then was very careful to fold the excess while putting the battery back in so the ribbon cable didn't kink. Your iPhone will be examined to verify eligibility, and then sent to the local Apple Repair Center. Check This Out
torqvette - July 22 my phone doesnt have a screw that connects the battery to the logic bored...is that a problem? misc - 11/10/2014 Reply When pressing the battery connector into the socket, the first time I pressed from bottom to top. Aug 1, 2012 11:28 AM Helpful (0) Reply options Link to this post by Bullitt08, Bullitt08 Aug 1, 2012 5:34 PM in response to Dxtra30 Level 1 (0 points) Aug 1,
The screen shattered, the dock connector barely worked, and the power button would't work at all. Cancel Melanie Rep: 1 Posted: 01/05/2013 Options Permalink History THis goes to show you how much apple really doesn't care about it's customers. Otherwise it went together fine, and I figured out for myselkf that the contact needs to be bent,,, loujudson - 10/19/2013 Reply What does the park that is gold and next Iphone 6s Power Button Stuck I've repaired 4 iPhone 4s now and this is the first time this has happened.
Should I buy a new power button ? Iphone 6 Lock Button Stuck Joshua - 06/01/2013 When reassembling, ensure the ribbon cables for the connector are between the silver metal and the circuit board. You will need to follow these instructions as well as remove the earpiece speaker, and partially remove the headphone jack (be VERY careful not to pull hard on those wires). More Bonuses Be VERY CAREFUL when doing this, because you don't want to have superglue wicking between the screw and the circuit board.
Sometimes the tool list jumps into two columns, and this makes it hard to look at as a "check list." I missed the fact that I needed a flathead screwdriver for Iphone 4s Power Button Replacement C Khripin - 03/23/2015 hi, the small gold prong (step 19) in my phone is fragile what should i do? I've removed several like this before; frequently I find the culprits for rounded out slots are ham-fisted people trying to do their own repairs in the past. No simple and/or easily searched support questions.
I assumed that there must have been a certain position that the bar must be in, so I came here, read the instruction. see this here what do i do? Iphone 6 Power Button Stuck The metal loop should be facing downwards and the outward edges should be on top. 2 comments This guide its not whel done. Iphone Power Button Not Working How To Turn On iCracked 295,817 views 13:57 How to Fix iPhone 4 Power Button Not Working - Duration: 10:07.
iPhoneRepairMia 1,230,880 views 8:32 iPhone 4 Power Button Repair NOT Replacement Guide Tutorial - AppleiPodParts.com - Duration: 17:24. http://pixelzs.com/power-button/iphone-3g-power-button-not-working.html I also watched a couple of YouTube videos so I could see how each component came apart, as well as the techniques and forces required to perform the disassembly (the most I had to install a new sensor cable, which I’m really glad I order because that's why the power button was not working. Steve Noland - 11/04/2010 Reply INCREDIBLE! How To Fix Iphone 4 Power Button Without Taking It Apart
No notes about this nor any picture - fail. But I feared they would go with that card since I read somewhere that apple can refuse warranty if it has marks on it. I even acknowledged that I probably technically didn't have much ground to stand on, but nonetheless that's how I feel. http://pixelzs.com/power-button/iphone-power-button-not-working.html Please follow the instructions below to have your sleep/wake button replaced.
It sometimes comes off the motherboard, with no adverse effects. Iphone 6 Lock Button Stuck Down Can't find a place for it anywhere!? In my case, I must not have threaded the cable through properly, so it was just a bit too short to reach the connector.
All my post was saying was: yes this happened to me. After $50 in parts/tools, he received $220 for the fixed phone. PressureFM - 05/03/2012 Reply I wasn't sure how to carefully detach the antennae. Iphone 6 Power Button Stuck Down The power button looked fine to my inexperienced eyes, and from reading comments and stories online, it became apparent that the switch on the power and sensor cable was what needed
etler - 10/31/2012 Reply Use a vacuum duster and a sharp tool to pry out the dust, this can increase the volume insanely! It's disruptive pretty much anywhere on your screen, but we found that the bottom third of the right hand side of our screen was the best for us. im not saying that apple is charging a fair price for the fix of that button, im saying that you bought what they were selling, and part of what they were this contact form Remove this now, and do not forget to re install it on assembly.
Now I can't restart my phone and I can't lock it. I could not believe I had the phone in what seemed to be a million little pieces. I decided to modify the button so that the small circular disc inset into the button had a bit more height. This was my first small electronics repair I had ever attempted, so I attribute my success to two things: (1) preparation prior to the repair, and (2) organization during the repair.
I would have gladly paid for them. permalinkembedsavegive gold[–]Sheriffz -1 points0 points1 point 3 years ago(0 children)Which iPhone do you have? A different guide (http://www.imore.com/how-diy-repair-stuc...) shows this very clearly in the respective step (http://www.imore.com/how-diy-repair-stuc...). After some thought I chose to use a pinhead of white elmers glue placed directly on the button with a pin.
I know this isn't the same issue as OP but it thought it was strangely relevant. the sleep button isn't part of the screen replacement so I know I didn't do anything to damage it. My Advice Make sure you clean the front and the back of the glass before gluing it in place. The wiring for the power button/proximity sensor goes underneath the earpiece speaker and sticks to the very small hole right next to the headphone jack.